Deciding Between a DIY Swap and a Professional Install
If the upgrade just swaps one part for another of the same kind, like a faucet, cabinet latch, or light fixture, you can often do it yourself. Once a project ties into your electrical system, propane, roof, hidden plumbing, or the RV's frame, a professional install is the safer bet. The real question is what happens if it goes wrong.
We'll be honest with you. Not every upgrade needs us. Plenty of RV owners are handy, and a lot of small changes are well within reach with basic tools and a free afternoon. We'd rather you save your money on the easy stuff and call us for the jobs that really count.
These are usually fine to tackle on your own:
-
Swapping a kitchen or bathroom faucet for one with the same fittings
-
Replacing cabinet latches, drawer pulls, door handles, and hinges
-
Changing out a shower head or adding a water-saving one
-
Putting in a plug-in or battery-powered accessory that doesn't need new wiring
-
Replacing a light fixture with a matching one on the same wires, with the power off
If your swap fits that list and you feel comfortable, go for it. If a screw strips or a fitting won't line up, that's often a small fix. You haven't put the rest of your rig at risk.
Things change when an upgrade reaches past the part itself. A new inverter, solar setup, or battery bank touches your whole electrical system, and a wiring mistake there can damage appliances or worse. Anything that connects to propane is a job for a trained hand. A new roof vent, fan, or antenna means cutting a hole in your roof. If that seal isn't done right, Florida's heavy rains will find it, and water can spread under the surface long before you notice a stain. Plumbing that runs behind walls or under floors is the same story. A slow drip you can't see can rot a subfloor.
Here's a simple way to decide. Ask yourself three questions:
-
Does this part connect to power, propane, or water lines I can't easily see?
-
Do I have to drill, cut, or seal anything on the roof or outside walls?
-
If I get it wrong, could it cost more than the part itself?
If you answered yes to any of those, it's worth having a pro take a look. Picture a new ceiling fan that's been sitting in its box for months because you're not sure about the roof cut. That hesitation is usually a good instinct.
When you do want help, our owners Logan and Keith are RVIA level 2 certified technicians, and we come to you. That means we can install it right where your RV is parked, whether that's your driveway, a campsite, or a storage lot. We'll get you an estimate within 24 to 48 hours, so you know what the job involves before anything gets started. And if you've already done part of the work yourself and just want someone to finish the tricky piece, that's fine with us too.
What Counts as an Upgrade or Accessory Job Here
An upgrade or accessory job is any change that makes your RV work better, look nicer, or fit the way you travel. It isn't a repair to fix something broken. It's a swap or an add-on you've been meaning to get around to. For us, that starts with the small stuff that makes daily RV life easier: minor fixtures, faucets, and hardware.
Here's the kind of work that fits in this group:
-
Kitchen and bathroom faucets, including ones that need new fittings or have hard-to-reach lines
-
Light fixtures and other small fixtures you'd like to update or replace
-
Cabinet, drawer, and door hardware like latches, hinges, pulls, and handles
-
Small accessories that need to be mounted, connected, or fitted to your rig
These jobs sound simple, and many are. But RV parts aren't always the same size or shape as the ones in a house. A faucet might need different fittings. A cabinet latch might have to fit a thin wall that can't hold a standard screw. Part of what we do is make sure the new piece really fits your RV, not just the picture on the box.
Some upgrades connect to a bigger system, so they have their own service pages. If you're thinking about new batteries or electrical changes, see our Electrical Systems and Battery Replacement page. A new awning or slide topper falls under Awning and Slide Topper Repair and Installation. Anything that means cutting into or resealing the roof belongs with Roof Repair and Re-seal and Replacement. If you're not sure where your project falls, just tell us what you have in mind. We'll sort it out with you.
We also want to be upfront about what we don't do. We don't handle motorhome oil changes or engine and chassis service. We don't work on Aqua-Hot hydronic heating systems. We don't do fiberglass body shop or paint work. If your project falls into one of those areas, you'll want a shop that focuses on that kind of work.
We're a fully mobile business. We don't sell parts over the counter, and we don't take drop-offs or shop appointments. Our Oviedo address is for mail and paperwork only. Every upgrade happens right where your RV is parked.
That works out well for most upgrade jobs. Your RV can stay in your driveway, at your campsite, or in your storage lot. We serve Lake, Orange, Seminole, Volusia, and Brevard counties, so whether you're here in Oviedo or parked farther out across Central Florida, we come to you. You don't have to hitch up and drive across town just to get a new faucet put in.
Once you tell us what you'd like done, we'll send you an estimate within 24 to 48 hours. That gives you a clear picture of the job before any work starts, so there are no surprises when we show up.
Why Certified Technicians Matter for Small Fixture Jobs
A faucet or a cabinet latch can feel too small to need a certified tech. But an RV isn't a house on wheels. It's a light, tightly packed space that shakes down the highway, runs on two kinds of power, and gets its water from a pump or a campground hookup. A small part put in the house way can cause trouble an RV owner won't see until it's a bigger job.
Here's what makes RV fixtures different:
-
Thin walls and cabinets. RV walls are often light panels, not studs and drywall. A screw that's too long can poke through to the outside, and one that's too short won't hold once the road starts shaking things.
-
Two power systems. Many RVs run lights and fans on 12-volt power and outlets on 120-volt power. A light fixture that looks right can be built for the wrong one.
-
RV plumbing. Water lines and fittings aren't always the same as home parts, and a water pump or park hookup can push water at a different pressure. A fitting that's a little off can drip slowly behind a cabinet where you'll never see it.
-
Constant movement. Every trip shakes your RV. Hardware that isn't mounted well loosens over time, and a cabinet door that pops open on a curve can send dishes across the floor.
Florida adds its own pressure. Our air is humid, and a hidden drip doesn't dry out fast. That's how a small faucet leak can turn into soft wood under the sink before you ever notice a smell.
That's why training matters, even on small jobs. Our owners hold RVIA level 2 certifications, and our team also includes an NRVIA Certified Inspector and holds a Lippert Certificate. In plain terms, we've trained on how RVs are built and how their systems connect. When we swap your faucet, we know what's behind the cabinet wall. When we hang a new light, we know which power it should run on.
Inspection training helps too. Someone trained to look over a whole RV tends to notice the small signs nearby, like a damp spot under the sink or a loose panel. If we spot something like that, we'll tell you straight, and we won't push you into work you don't need. If you'd like a full look at your rig, that's what our Pre-Purchase and Annual Inspections are for.
Most of all, you get a fixture that fits and holds up on the road, plus the peace of mind that nothing behind it was knocked loose. Since we come to you and send your estimate within 24 to 48 hours, getting it done right doesn't cost you a trip to a shop or a long wait.
How the Mobile Visit Works for Upgrades and Accessories
A mobile visit is pretty simple from your side. You tell us what you'd like done and where your RV is parked. You look over your estimate, which arrives within a day or two. Then the work happens right there, whether that's your driveway, a campsite, or a storage lot. A little prep on your end helps the day go smoothly and makes sure the new part works the way you hoped.
When you reach out, the more we know about the job, the clearer your estimate can be. Here's what helps:
-
What you want changed, like the kitchen faucet, a bathroom light, or the latches on a few overhead cabinets
-
The year, make, and model of your RV, if you have it handy
-
A few photos of the old part and the area around it, such as the lines under your sink or the spot where a fixture mounts
-
Whether you've already bought the new part. Keep the box and paperwork with it
-
Where the RV is parked and whether it has power and water hooked up there
That last point matters more than people expect. A rig sitting in a storage lot with no shore power and empty tanks is a different setup than one plugged in at home. If a new light or a water fixture needs to be tested once it's in, it helps to know ahead of time what's available on site.
Before the visit, take a few minutes to get the spot ready:
-
If your RV is at a storage facility or campground, check with the office first. Some places have rules about outside technicians, gate access, or work hours.
-
Make sure there's a clear path to the RV door and room to move around the rig.
-
Empty the cabinet under the sink for faucet jobs, and clear out any drawers or cabinets getting new hardware.
-
Know where your water pump switch, water hookup, and power hookup are, so they can be shut off if the job needs it.
-
Keep pets settled somewhere comfortable, away from the work area and open doors.
Summer in Central Florida also brings hot, sticky afternoons and pop-up storms. If you can, plan to have the RV opened up and aired out a bit before the visit, especially if it's been closed up in a storage lot for weeks. It makes the inside a lot more pleasant to work in.
After the job, give the new part a quick test of your own. It only takes a few minutes and gives you peace of mind:
-
Run a new faucet hot and cold, then peek under the sink again the next day for any dampness.
-
Turn new lights on and off a few times.
-
Open and close cabinets and drawers with new hardware, and make sure the doors latch firmly.
-
After your first trip down the road, check that new hardware and fixtures still feel snug.
If something doesn't look or feel right, tell us. We'd much rather hear about a small concern early than have you wonder about it on your next camping weekend.
What Drives Cost on a Fixture or Hardware Upgrade
There's no single price for "a new faucet" or "new cabinet latches," because the part is only one piece of the cost. What really moves the number is how easy the old part is to reach, whether the new one fits your rig as-is, and what turns up once the old piece comes off.
Here's what tends to make a job bigger or smaller.
-
The part itself. A basic replacement costs less than a fancier model. If you've already bought it, the cost is mostly labor. If it needs to be sourced, that adds to the total.
-
Fit and compatibility. When the new part matches the old one, the swap is quick. If it needs adapters, new fittings, or a different mounting spot, the job takes more time and materials.
-
Access. A faucet with open space under the sink is simpler than one with lines tucked behind a panel or a water heater. Hard-to-reach spots take longer.
-
What's behind the old part. A stuck fitting, stripped screw holes, or soft wood under a leaky sink can turn a simple swap into a small repair. Nobody can know for sure until the old piece is off.
-
Wiring changes. A light on the same wires is simple. A fixture that runs on a different power system, as we covered earlier, or needs a new switch adds work.
-
How many items you bundle. Doing several faucets, fixtures, or a full set of cabinet hardware in one visit is usually a better use of time than spreading them out.
It also helps to know how mobile RV service is often priced across the industry. Some providers charge by the hour. Some charge a flat rate for common jobs. Many add a trip or service call fee for coming to you. None of these is wrong, but you should know which one you're getting so you can compare fairly. A low hourly rate can end up costing more on a slow job, and a flat rate may not cover surprises found behind the wall.
Before you hire anyone for an upgrade, these questions are worth asking:
-
Is the price by the hour, a flat rate, or a mix?
-
Is there a trip or service call charge, and is it included in the estimate?
-
Does the estimate include the part, or just the labor?
-
What happens if you find damage once the old part is off? Will you check with me before doing more?
-
Can I save by bundling a few small jobs into one visit?
We started this business because we'd seen RV owners, ourselves included, get hit with surprise charges and runarounds. That's why we put the job in writing before any work starts. Your estimate arrives within 24 to 48 hours, so you can see what's involved and decide without pressure. If we find something unexpected behind a cabinet wall, we'll show you and talk it through before going further.
The more you tell us up front, the closer that estimate will be. Photos of the old part and the area around it go a long way.
Frequently Asked Questions
Do I need to buy the faucet or fixture myself before you come out?
You can, and it often helps. If you already have the part, keep the box and paperwork with it so we can check fittings and specs before the visit. If you haven't bought anything yet, tell us what you want changed and we can factor sourcing it into your estimate. Either way works, so pick whatever is easier for you.
Can you install an upgrade while my RV is parked at a storage lot instead of my home?
Yes, we come to you at a storage lot, campsite, or your driveway since we're a fully mobile service. Just check with the storage office first, since some facilities have rules about outside technicians, gate access, or work hours. Also let us know if the lot has power and water hookups available, since that affects how we test a new fixture once it's installed.
What if you open up the cabinet and find a bigger problem than expected?
We'll stop and show you what we found before doing any more work. Things like a stuck fitting, stripped screw holes, or soft wood under a leaky sink sometimes turn up once the old part comes off, and nobody can know for sure until then. You decide how to move forward, and nothing extra gets done without you knowing first.
